Miller Kristin S, Edelstein Lena, Connizzo Brianne K, Soslowsky Louis J
McKay Orthopaedic Research Laboratory, University of Pennsylvania, Philadelphia, PA 19104-6081, USA.
J Biomech Eng. 2012 Mar;134(3):031007. doi: 10.1115/1.4006340.
Repeatedly and consistently measuring the mechanical properties of tendon is important but presents a challenge. Preconditioning can provide tendons with a consistent loading history to make comparisons between groups from mechanical testing experiments. However, the specific mechanisms occurring during preconditioning are unknown. Previous studies have suggested that microstructural changes, such as collagen fiber re-alignment, may be a result of preconditioning. Local collagen fiber re-alignment is quantified throughout tensile mechanical testing using a testing system integrated with a polarized light setup, consisting of a backlight, 90 deg-offset rotating polarizer sheets on each side of the test sample, and a digital camera, in a rat supraspinatus tendon model, and corresponding mechanical properties are measured. Local circular variance values are compared throughout the mechanical test to determine if and where collagen fiber re-alignment occurred. The inhomogeneity of the tendon is examined by comparing local circular variance values, optical moduli and optical transition strain values. Although the largest amount of collagen fiber re-alignment was found during preconditioning, significant re-alignment was also demonstrated in the toe and linear regions of the mechanical test. No significant changes in re-alignment were seen during stress relaxation. The insertion site of the supraspinatus tendon demonstrated a lower linear modulus and a more disorganized collagen fiber distribution throughout all mechanical testing points compared to the tendon midsubstance. This study identified a correlation between collagen fiber re-alignment and preconditioning and suggests that collagen fiber re-alignment may be a potential mechanism of preconditioning and merits further investigation. In particular, the conditions necessary for collagen fibers to re-orient away from the direction of loading and the dependency of collagen reorganization on its initial distribution must be examined.
反复且持续地测量肌腱的力学性能很重要,但也面临挑战。预处理可为肌腱提供一致的加载历史,以便在力学测试实验中对不同组进行比较。然而,预处理过程中发生的具体机制尚不清楚。先前的研究表明,微观结构变化,如胶原纤维重新排列,可能是预处理的结果。在大鼠冈上肌腱模型中,使用集成了偏振光装置的测试系统,在整个拉伸力学测试过程中对局部胶原纤维重新排列进行量化,该系统包括一个背光源、位于测试样品两侧的90度偏移旋转偏振片以及一台数码相机,并测量相应的力学性能。在整个力学测试过程中比较局部圆方差值,以确定胶原纤维是否以及在何处发生了重新排列。通过比较局部圆方差值、光学模量和光学转变应变值来检查肌腱的不均匀性。尽管在预处理过程中发现了最大量的胶原纤维重新排列,但在力学测试的趾部和线性区域也显示出明显的重新排列。在应力松弛过程中,重新排列未见明显变化。与肌腱中部相比,冈上肌腱的附着部位在所有力学测试点均表现出较低的线性模量和更无序的胶原纤维分布。本研究确定了胶原纤维重新排列与预处理之间的相关性,并表明胶原纤维重新排列可能是预处理的一种潜在机制,值得进一步研究。特别是,必须研究胶原纤维从加载方向重新定向所需的条件以及胶原重组对其初始分布的依赖性。