Suppr超能文献

种植体-基台金属表面单一种属和共培养牙周致病菌早期定植的评估。

An assessment of early colonisation of implant-abutment metal surfaces by single species and co-cultured bacterial periodontal pathogens.

机构信息

Oral and Biomedical Sciences, School of Dentistry, Cardiff University, Heath Park, Cardiff, CF14 4XY, UK.

Oral and Biomedical Sciences, School of Dentistry, Cardiff University, Heath Park, Cardiff, CF14 4XY, UK; Cardiff Institute of Tissue Engineering and Repair, Cardiff University, Cardiff, UK.

出版信息

J Dent. 2016 Oct;53:64-72. doi: 10.1016/j.jdent.2016.07.013. Epub 2016 Jul 26.

Abstract

OBJECTIVE

Numerous studies have proposed that smooth metal surfaces reduce initial bacterial attachment in the establishment of an early biofilm formation. However, these studies have largely examined single bacterial species, which are not always relevant as pathogens identified as initiators of inflammatory peri-implantitis. This study investigated the adherence of four periodontally-relevant bacterial species to implant and abutment surfaces in current clinical use.

METHODS

Discs of polished cobalt chromium (CoCr-polished) and milled titanium (Ti-milled), representing two clinically relevant surfaces, were prepared and surfaces were characterised. Bacterial species Porphyromonas gingivalis, Fusobacterium nucleatum, Prevotella intermedia and Aggregatibacter actinomycetemcomitans were cultured to mid-log or stationary growth phase. Co-cultures of P. gingivalis, F. nucleatum and P. gingivalis, F. nucleatum, Pr. intermedia were similarly prepared. Bacteria were inoculated onto discs for 2h, stained with a live/dead fluorescent stain and percentage bacterial coverage was calculated by confocal microscopy and image analysis.

RESULTS

CoCr-polished discs had smooth surfaces with gentle valley structures, whilst Ti-milled discs had sharp edged peaks. Both discs demonstrated a partial wetting ability capable of initiating bacterial adhesion. P. gingivalis, F. nucleatum and co-cultures, at both mid-log and stationary concentrations, demonstrated equally high coverage of both the smooth CoCr-polished and the rougher Ti-milled metal surfaces. Pr. intermedia and A. actinomycetemcomitans demonstrated lower surface coverage which was slightly higher for Ti-milled.

CONCLUSION

Variability was noted in the adherence potential for the respective periodontal pathogens examined. Particularly high adherence was noted for P. gingivalis and F. nucleatum, despite the manufacture of a smooth surface.

CLINICAL SIGNIFICANCE

Both surfaces studied may be used at implant-abutment junctions and both possess an ability to establish a bacterial biofilm containing a periodontally-relevant species. These surfaces are thus able to facilitate the apical migration of bacteria associated with peri-implantitis.

摘要

目的

许多研究表明,光滑的金属表面可减少早期生物膜形成中初始细菌附着。然而,这些研究大多检查了单一细菌物种,而这些物种并不总是与被确定为引发炎症性种植体周围炎的病原体相关。本研究调查了目前临床使用的种植体和基台表面上四种与牙周病相关的细菌的附着。

方法

制备了抛光钴铬(CoCr 抛光)和铣削钛(Ti 铣削)代表两种临床相关表面的圆盘,并对表面进行了表征。培养牙龈卟啉单胞菌、核梭杆菌、中间普氏菌和伴放线放线杆菌至中对数或静止生长阶段。同样制备了牙龈卟啉单胞菌、核梭杆菌和牙龈卟啉单胞菌、核梭杆菌、中间普氏菌的共培养物。将细菌接种到圆盘上 2 小时,用活/死荧光染色剂染色,通过共聚焦显微镜和图像分析计算细菌覆盖率。

结果

CoCr 抛光圆盘表面光滑,具有温和的山谷结构,而 Ti 铣削圆盘则具有锋利的边缘峰。两个圆盘都显示出部分润湿能力,能够引发细菌附着。在中对数和静止浓度下,牙龈卟啉单胞菌、核梭杆菌和共培养物都表现出对光滑 CoCr 抛光和更粗糙 Ti 铣削金属表面同样高的覆盖率。中间普氏菌和伴放线放线杆菌的表面覆盖率较低,Ti 铣削时略高。

结论

在所检查的牙周病相关病原体中,注意到粘附潜力存在差异。尽管制造了光滑表面,但牙龈卟啉单胞菌和核梭杆菌的粘附性特别高。

临床意义

研究中两种表面都可用于种植体-基台连接处,并且都具有建立含有牙周病相关物种的细菌生物膜的能力。因此,这些表面能够促进与种植体周围炎相关的细菌向根尖迁移。

文献AI研究员

20分钟写一篇综述,助力文献阅读效率提升50倍。

立即体验

用中文搜PubMed

大模型驱动的PubMed中文搜索引擎

马上搜索

文档翻译

学术文献翻译模型,支持多种主流文档格式。

立即体验