1 Department of Radiation Oncology, University of California Davis Comprehensive Cancer Center, Sacramento, CA, USA.
Technol Cancer Res Treat. 2019 Jan 1;18:1533033819865623. doi: 10.1177/1533033819865623.
Palliation of advanced disease using radiotherapy can create difficult clinical situations where standard computed tomography simulation and immobilization techniques are not feasible. We developed a linear accelerator-based radiotherapy simulation technique using nonstandard patient positioning for head and neck palliation using on-board kilovoltage cone-beam computed tomography for 3-D volumetric planning and rapid treatment. Material and Methods: We proved cone-beam computed tomography simulation feasibility for semi-upright patient positioning using an anthropomorphic phantom on a clinical Elekta-Synergy linear accelerator. Cone-beam computed tomography imaging parameters were optimized for high-resolution image reconstruction and to ensure mechanical clearance. The patient was simulated using a cone-beam computed tomography-based approach and the cone-beam computed tomography digital imaging and communications in medicine file was imported to the treatment planning software to generate radiotherapy target volumes. Rapid planning was achieved by using a 3-level bulk density correction for air, soft tissue, and bone set at 0, 1.0, and 1.4 g/cm, respectively.
Patient volumetric imaging was obtained through cone-beam computed tomography simulation and treatment was delivered as planned without incident. Bulk density corrections were verified against conventionally simulated patients where differences were less than 1%. Conclusion: We successfully developed and employed a semi-upright kilovoltage cone-beam computed tomography-based head and neck simulation and treatment planning method for 3-D conformal radiotherapy delivery. This approach provides 3-D documentation of the radiotherapy plan and allows tabulation of quantitative spatial dose information which is valuable if additional palliative treatments are needed in the future. This is a potentially valuable technique that has broad clinical applicability for benign and palliative treatments across multiple disease sites-particularly where standard supine simulation and immobilization techniques are not possible.
使用放射疗法对晚期疾病进行姑息治疗可能会导致一些困难的临床情况,在这些情况下,标准的计算机断层扫描模拟和固定技术是不可行的。我们开发了一种基于线性加速器的放射治疗模拟技术,该技术使用非标准的患者定位,对头颈部姑息治疗使用机载千伏锥形束计算机断层扫描进行 3D 容积规划和快速治疗。
我们使用临床 Elekta-Synergy 线性加速器上的人体模型证明了半直立患者定位的锥形束计算机断层扫描模拟的可行性。优化了锥形束计算机断层扫描成像参数,以实现高分辨率图像重建和确保机械间隙。使用锥形束计算机断层扫描方法对患者进行模拟,并将锥形束计算机断层扫描数字成像和通信医疗文件导入治疗计划软件,以生成放射治疗靶区。通过对空气、软组织和骨骼分别设置 0、1.0 和 1.4g/cm 的 3 级体密度校正,实现了快速规划。
通过锥形束计算机断层扫描模拟获得了患者的体积成像,并且按照计划进行了治疗,没有出现任何问题。体密度校正与常规模拟患者进行了验证,差异小于 1%。
我们成功开发并采用了一种半直立千伏锥形束计算机断层扫描头颈部模拟和治疗计划方法,用于 3D 适形放射治疗。这种方法提供了放射治疗计划的 3D 文档,并允许对定量空间剂量信息进行制表,如果将来需要额外的姑息性治疗,这是非常有价值的。这是一种潜在有价值的技术,具有广泛的临床适用性,可用于多个疾病部位的良性和姑息性治疗,特别是在无法进行标准仰卧位模拟和固定技术的情况下。