Department of Biomaterials, New York University College of Dentistry, New York, New York, USA.
Department of Mechanical and Aerospace Engineering, New York University Tandon School of Engineering, Brooklyn, New York, USA.
J Biomed Mater Res B Appl Biomater. 2022 Jan;110(1):195-209. doi: 10.1002/jbm.b.34902. Epub 2021 Jul 1.
Injuries requiring resection of tissue followed by autogenous bone transfer may be prone to infection by Staphylococcus aureus, impeding recovery and increasing medical costs. For critical sized defects, the common approach to reconstruction is a tissue transfer procedure but is subject to limitations (e.g., donor site morbidity, cost, operating time). Utilizing beta tricalcium phosphate (β-TCP) as bone grafting material augmented with silver (Ag), a custom graft may be 3D printed to overcome limitations and minimize potential infections.
Scaffolds were 3D printed and augmented with Ag by external attack on the surface by silver nitrate (AgNO ) at varying concentrations (0.1, 1.0, 10% wt/wt of scaffold). The augmented scaffolds were evaluated utilizing X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR), and inductively coupled plasma mass spectroscopy (ICP-MS) to verify the presence of Ag and phosphate (PO ) groups followed by electron microscopy, thermogravimetric analysis (TGA), and differential scanning calorimetry (DSC) to gather information of chemical and physical properties. Preliminary biocompatibility and bactericidal capacity of the scaffolds were tested using human osteoprogenitor (hOP) cells and methicillin-sensitive S. aureus strain, respectively.
XRD, FTIR, ICP-MS, TGA, and DSC confirmed presence of Ag and PO groups, whereas electron microscopy showed a decrease in Ca and an increase in Ag ions, decreasing Ca/P ratio with increasing surfactant concentrations. PrestoBlue assays yielded an increase in fluorescence cell counts among experimental groups with lower concentrations of Ag characterized by their characteristic trapezoidal shape whereas cytotoxicity was observed at higher concentrations. Similar observations were made with alkaline phosphatase assays. Antimicrobial evaluation showed reduced colony-forming units (CFU) among all experimental groups when compared to 100% β-TCP. β-TCP scaffolds augmented with Ag ions facilitate antibacterial effects while promoting osteoblast adhesion and proliferation.
需要切除组织并进行自体骨移植的损伤可能容易受到金黄色葡萄球菌的感染,从而阻碍恢复并增加医疗费用。对于临界尺寸的缺损,常见的重建方法是组织转移手术,但存在局限性(例如,供体部位发病率、成本、手术时间)。利用β-磷酸三钙(β-TCP)作为骨移植物材料,并添加银(Ag),可以使用定制移植物通过 3D 打印来克服限制并最大程度地减少潜在感染。
通过将硝酸银(AgNO3)以不同浓度(支架重量的 0.1、1.0、10%wt/wt)施加于表面,对支架进行 3D 打印和 Ag 增强。通过 X 射线衍射(XRD)、傅里叶变换红外光谱(FTIR)和电感耦合等离子体质谱(ICP-MS)对增强的支架进行评估,以验证 Ag 和磷酸盐(PO4)基团的存在,然后通过电子显微镜、热重分析(TGA)和差示扫描量热法(DSC)收集化学和物理性质信息。使用人成骨前体细胞(hOP)细胞和耐甲氧西林敏感的金黄色葡萄球菌株分别测试了支架的初步生物相容性和杀菌能力。
XRD、FTIR、ICP-MS、TGA 和 DSC 证实了 Ag 和 PO4 基团的存在,而电子显微镜显示 Ca 减少和 Ag 离子增加,随着表面活性剂浓度的增加,Ca/P 比降低。PrestoBlue 测定法显示,在具有特征梯形形状的较低 Ag 浓度的实验组中,荧光细胞计数增加,而在较高浓度时观察到细胞毒性。碱性磷酸酶测定也有类似的观察结果。与 100%β-TCP 相比,所有实验组的抗菌评估均显示菌落形成单位(CFU)减少。添加 Ag 离子的β-TCP 支架可促进抗菌作用,同时促进成骨细胞的黏附和增殖。