Panchal Nikhilkumar, Vinu R
Department of Chemical Engineering and National Centre for Combustion Research and Development, Indian Institute of Technology Madras, Chennai 600036, India.
J Anal Appl Pyrolysis. 2023 Mar;170:105870. doi: 10.1016/j.jaap.2023.105870. Epub 2023 Jan 18.
During the COVID-19 pandemic, the world saw an exponential surge in the production of Personal Protective Equipment (PPE) kits, which eventually got discarded in the biomedical waste stream. In this study, thirteen different polymer samples from the PPE kit were collected and characterized using Fourier transform infrared spectrometer, thermogravimetric analysis, and analytical pyrolysis-gas chromatograph/mass spectrometry. The characterization data showed that about 94 % by mass of components were made of only three polymers, viz. polypropylene (PP, 75.6 wt %), polyethylene terephthalate (PET, 12.5 wt %), and polycarbonate (PC, 6 wt %). The analytical pyrolysis of the PPE coverall suit (PP) yielded mainly alkenes containing 2,4-dimethyl-1-heptene as the major compound with 17 wt % yield at 600 °C. The pyrolysates from face shield (PET) were rich in benzoic acid (5.8 wt %) and acetophenone (4.8 wt %), while those from safety goggles (PC) were rich in phenol (17.6 wt %) and p-cresol (12.4 wt %) at 600 °C. HZSM-5 and HY zeolites were used for the catalytic upgradation of pyrolysates especially from PP, PET and PC. The temperature and feed-to-catalyst ratio were optimized by performing catalytic fast pyrolysis experiments at 500 °C, 600 °C and 700 °C with different feed-to-catalyst ratios 1:2, 1:4, and 1:6 (w/w). The yield of aromatic hydrocarbons, viz., BTEX (benzene, toluene, ethylbenzene, xylenes) and naphthalene, was maximum (∼25.7 wt %) from PP coverall when HY catalyst was used at 600 °C and 1:6 (w/w) loading. In the case of PET face shield, the total yield of BTEX, naphthalene and biphenyl was maximum (27.9 wt %) at 600 °C and 1:4 (w/w) of HZSM-5, while in the case of PC goggles, it was maximum (18.6 wt %) at 700 °C and 1:4 (w/w) of HY. This study shows that the entire PPE kit can be valorized via catalytic fast pyrolysis to generate petrochemical products and platform molecules like monoaromatic hydrocarbons at high selectivities.
在新冠疫情期间,全球个人防护装备(PPE)套件的产量呈指数级增长,这些套件最终被当作生物医疗废弃物处理。在本研究中,从PPE套件中收集了13种不同的聚合物样品,并使用傅里叶变换红外光谱仪、热重分析以及分析热解-气相色谱/质谱联用仪进行了表征。表征数据显示,按质量计约94%的组分仅由三种聚合物制成,即聚丙烯(PP,75.6 wt%)、聚对苯二甲酸乙二酯(PET,12.5 wt%)和聚碳酸酯(PC,6 wt%)。PPE工作服(PP)的分析热解在600℃时主要生成含有2,4-二甲基-1-庚烯的烯烃,其主要化合物产率为17 wt%。面罩(PET)的热解产物富含苯甲酸(5.8 wt%)和苯乙酮(4.8 wt%),而安全护目镜(PC)的热解产物在600℃时富含苯酚(17.6 wt%)和对甲酚(12.4 wt%)。HZSM-5和HY沸石用于热解产物尤其是来自PP、PET和PC的热解产物的催化升级。通过在500℃、600℃和700℃下以1:2、1:4和1:6(w/w)的不同进料与催化剂比例进行催化快速热解实验,优化了温度和进料与催化剂比例。当在600℃和1:6(w/w)的负载量下使用HY催化剂时,PP工作服的芳烃(即BTEX(苯、甲苯、乙苯、二甲苯)和萘)产率最高(约25.7 wt%)。对于PET面罩,在600℃和1:4(w/w)的HZSM-5用量下,BTEX、萘和联苯的总产率最高(27.9 wt%),而对于PC护目镜,在700℃和1:4(w/w)的HY用量下,总产率最高(18.6 wt%)。本研究表明,整个PPE套件可通过催化快速热解实现增值,以高选择性生成石化产品和平台分子,如单芳烃。