Guccione J M, McCulloch A D, Waldman L K
Department of Applied Mechanics and Engineering Sciences (Bioengineering), University of California, San Diego, La Jolla 92093-0412.
J Biomech Eng. 1991 Feb;113(1):42-55. doi: 10.1115/1.2894084.
The equatorial region of the canine left ventricle was modeled as a thick-walled cylinder consisting of an incompressible hyperelastic material with homogeneous exponential properties. The anisotropic properties of the passive myocardium were assumed to be locally transversely isotropic with respect to a fiber axis whose orientation varied linearly across the wall. Simultaneous inflation, extension, and torsion were applied to the cylinder to produce epicardial strains that were measured previously in the potassium-arrested dog heart. Residual stress in the unloaded state was included by considering the stress-free configuration to be a warped cylindrical arc. In the special case of isotropic material properties, torsion and residual stress both significantly reduced the high circumferential stress peaks predicted at the endocardium by previous models. However, a resultant axial force and moment were necessary to cause the observed epicardial deformations. Therefore, the anisotropic material parameters were found that minimized these resultants and allowed the prescribed displacements to occur subject to the known ventricular pressure loads. The global minimum solution of this parameter optimization problem indicated that the stiffness of passive myocardium (defined for a 20 percent equibiaxial extension) would be 2.4 to 6.6 times greater in the fiber direction than in the transverse plane for a broad range of assumed fiber angle distributions and residual stresses. This agrees with the results of biaxial tissue testing. The predicted transmural distributions of fiber stress were relatively flat with slight peaks in the subepicardium, and the fiber strain profiles agreed closely with experimentally observed sarcomere length distributions. The results indicate that torsion, residual stress and material anisotropy associated with the fiber architecture all can act to reduce endocardial stress gradients in the passive left ventricle.
犬左心室的赤道区域被建模为一个厚壁圆柱体,由具有均匀指数特性的不可压缩超弹性材料组成。假定被动心肌的各向异性特性相对于纤维轴局部横向各向同性,该纤维轴的方向在整个壁上呈线性变化。对圆柱体同时施加膨胀、伸展和扭转,以产生先前在钾停搏犬心脏中测量到的心外膜应变。通过将无应力构型视为扭曲的圆柱弧来考虑卸载状态下的残余应力。在各向同性材料特性的特殊情况下,扭转和残余应力均显著降低了先前模型预测的心内膜处的高周向应力峰值。然而,需要一个合力轴向力和力矩来引起观察到的心外膜变形。因此,找到了各向异性材料参数,这些参数使这些合力最小化,并允许在已知心室压力负荷下发生规定的位移。这个参数优化问题的全局最小解表明,对于广泛的假定纤维角度分布和残余应力,被动心肌的刚度(定义为20%等双轴伸展时)在纤维方向上比在横向平面上大2.4至6.6倍。这与双轴组织测试的结果一致。预测的纤维应力跨壁分布相对平坦,在心外膜下有轻微峰值,并且纤维应变曲线与实验观察到的肌节长度分布密切吻合。结果表明,与纤维结构相关的扭转、残余应力和材料各向异性都可以起到降低被动左心室心内膜应力梯度的作用。