Suppr超能文献

焊接作业中六价铬的暴露和控制。

Hexavalent chromium exposure and control in welding tasks.

机构信息

Department of Environmental Health Sciences, University of Michigan School of Public Health, Ann Arbor, Michigan 48109, USA.

出版信息

J Occup Environ Hyg. 2010 Nov;7(11):607-15. doi: 10.1080/15459624.2010.510105.

Abstract

Studies of exposure to the lung carcinogen hexavalent chromium (CrVI) from welding tasks are limited, especially within the construction industry where overexposure may be common. In addition, despite the OSHA requirement that the use of engineering controls such as local exhaust ventilation (LEV) first be considered before relying on other strategies to reduce worker exposure to CrVI, data on the effectiveness of LEV to reduce CrVI exposures from welding are lacking. The goal of the present study was to characterize breathing zone air concentrations of CrVI during welding tasks and primary contributing factors in four datasets: (1) OSHA compliance data; (2) a publicly available database from The Welding Institute (TWI); (3) field survey data of construction welders collected by the Center for Construction Research and Training (CPWR); and (4) controlled welding trials conducted by CPWR to assess the effectiveness of a portable LEV unit to reduce CrVI exposure. In the OSHA (n = 181) and TWI (n = 124) datasets, which included very few samples from the construction industry, the OSHA permissible exposure level (PEL) for CrVI (5 μg/m(3)) was exceeded in 9% and 13% of samples, respectively. CrVI concentrations measured in the CPWR field surveys (n = 43) were considerably higher, and 25% of samples exceeded the PEL. In the TWI and CPWR datasets, base metal, welding process, and LEV use were important predictors of CrVI concentrations. Only weak-to-moderate correlations were found between total particulate matter and CrVI, suggesting that total particulate matter concentrations are not a good surrogate for CrVI exposure in retrospective studies. Finally, in the controlled welding trials, LEV reduced median CrVI concentrations by 68% (p = 0.02). In conclusion, overexposure to CrVI in stainless steel welding is likely widespread, especially in certain operations such as shielded metal arc welding, which is commonly used in construction. However, exposure could be substantially reduced with proper use of LEV.

摘要

针对焊接作业中六价铬(CrVI)暴露的研究较为有限,尤其是在建筑行业,可能存在过度暴露的情况。此外,尽管职业安全与健康管理局(OSHA)要求,在依赖其他策略来降低工人接触 CrVI 的风险之前,应首先考虑采用工程控制措施,如局部排气通风(LEV),但目前缺乏关于 LEV 降低焊接过程中 CrVI 暴露的有效性的数据。本研究的目的是在四个数据集(1)OSHA 合规数据;(2)焊接研究所(TWI)公开可用的数据库;(3)建筑焊工职业安全与健康研究所(CPWR)进行的现场调查数据;(4)CPWR 进行的受控焊接试验中,对焊接作业时呼吸区空气中的 CrVI 浓度进行特征描述,并确定主要影响因素。在 OSHA(n = 181)和 TWI(n = 124)数据集(包括来自建筑行业的极少数样本)中,CrVI 的 OSHA 可接受暴露水平(PEL)(5μg/m(3))分别有 9%和 13%的样本超标。CPWR 现场调查(n = 43)中测量的 CrVI 浓度要高得多,有 25%的样本超过了 PEL。在 TWI 和 CPWR 数据集,母材、焊接工艺和 LEV 的使用是 CrVI 浓度的重要预测因素。仅发现总颗粒物与 CrVI 之间存在弱至中度相关性,这表明在回顾性研究中,总颗粒物浓度不能很好地替代 CrVI 暴露。最后,在受控焊接试验中,LEV 将 CrVI 的中位数浓度降低了 68%(p = 0.02)。总之,不锈钢焊接中 CrVI 的过度暴露可能很普遍,尤其是在某些操作中,如建筑行业中常用的金属电弧焊。但是,通过正确使用 LEV,暴露可以大大降低。

文献AI研究员

20分钟写一篇综述,助力文献阅读效率提升50倍。

立即体验

用中文搜PubMed

大模型驱动的PubMed中文搜索引擎

马上搜索

文档翻译

学术文献翻译模型,支持多种主流文档格式。

立即体验