Department of Cardiovascular Engineering, Institute of Applied Medical Engineering, Helmholtz Institute, RWTH Aachen University, Aachen, Germany.
Artif Organs. 2010 Oct;34(10):798-806. doi: 10.1111/j.1525-1594.2010.01098.x.
Tip geometry and placement of rotary blood pump inflow and outflow cannulae influence the dynamics of flow within the ventricle and aortic branch. Cannulation, therefore, directly influences the potential for thrombus formation and end-organ perfusion during ventricular assist device (VAD) support or cardiopulmonary bypass (CPB). The purpose of this study was to investigate the effect of various inflow/outflow cannula tip geometries and positions on ventricular and greater vessel flow patterns to evaluate ventricular washout and impact on cerebral perfusion. Transparent models of a dilated cardiomyopathic ventricle and an aortic branch were reconstructed from magnetic resonance imaging data to allow flow measurements using particle image velocimetry (PIV). The contractile function of the failing ventricle was reproduced pneumatically, and supported with a rotary pump. Flow patterns were visualized around VAD inflow cannulae, with various tip geometries placed in three positions in the ventricle. The outflow cannula was placed in the subclavian artery and at several positions in the aorta. Flow patterns were measured using PIV and used to validate an aortic flow computational fluid dynamic study. The PIV technique indicated that locating the inflow tip in the left ventricular outflow tract improved complete ventricular washout while the tip geometry had a smaller influence. However, side holes in the inflow cannula improved washout in all cases. The PIV results confirmed that the positioning and orientation of the outflow cannula in the aortic branch had a high impact on the flow pattern in the vessels, with a negative blood flow in the right carotid artery observed in some cases. Cannula placement within the ventricle had a high influence on chamber washout. The positioning of the outflow cannula directly influences the flow through the greater vessels, and may be responsible for the occasional reduction in cerebral perfusion seen in clinical CPB.
尖端几何形状和旋转血泵的流入和流出插管的位置会影响心室和主动脉分支内的流动动力学。因此,插管直接影响心室辅助装置(VAD)支持或心肺旁路(CPB)期间血栓形成和终末器官灌注的潜力。本研究的目的是研究各种流入/流出插管尖端几何形状和位置对心室和大血管流动模式的影响,以评估心室冲洗和对脑灌注的影响。使用粒子图像测速(PIV)从磁共振成像数据重建扩张型心肌病心室和主动脉分支的透明模型,以进行流量测量。使用旋转泵气动复制衰竭心室的收缩功能,并支持它。在 VAD 流入插管周围可视化流动模式,将各种尖端几何形状放置在心室中的三个位置。流出插管放置在锁骨下动脉中,并放置在主动脉的几个位置。使用 PIV 测量流动模式,并用于验证主动脉流动计算流体动力学研究。PIV 技术表明,将流入尖端定位在左心室流出道中可以改善完全心室冲洗,而尖端几何形状的影响较小。然而,流入插管中的侧孔在所有情况下都改善了冲洗。PIV 结果证实,流出插管在主动脉分支中的定位和方向对血管中的流动模式有很大影响,在某些情况下观察到右颈动脉出现负血流。插管在心室中的放置对腔室冲洗有很大影响。流出插管的定位直接影响大血管中的流动,并且可能是临床 CPB 中偶尔观察到脑灌注减少的原因。