Cheng YuJia, Bai Liyang, Yu Guang, Zhang Xiaohong
Mechanical and Electrical Engineering Institute, University of Electronic Science and Technology of China, Zhongshan Institute, Zhongshan 528402, China.
State Grid Tianjin Wuqing Electric Power Supply Company, Tianjin 301700, China.
Materials (Basel). 2018 Dec 20;12(1):5. doi: 10.3390/ma12010005.
The melt blending was used to prepare 3 wt% ZnO/low density polyethylene (ZnO/LDPE) nanocomposites in this article. The effect of different inorganic ZnO particles doping on the dielectrical property and crystal habit of LDPE matrix was explored. The nanoparticles size was 9 nm, 30 nm, 100 nm, and 200 nm respectively. Scanning electron microscope (SEM) was used to characterize ZnO nanoparticles whereas differential scanning calorimetry (DSC) was used to make thermal characterization of the samples. Besides, the AC (alternating current), DC (direct current breakdown characteristics and electrical conductivity of the nanocomposites was studied in this article. The experimental results showed that nano-ZnO/LDPE composites had the advantages such as small crystal size, high crystallization rate and crystallinity owing to nano-ZnO particles doping, when doping nano-ZnO particles size was 30 nm, the ZnO/LDPE nanocomposite crystallinity crest value 39.77% appeared. At the mean time, the DC and AC breakdown field strength values of composites were 138.0 kV/mm and 340.4 kV/mm respectively. They were the maximal values which improved 8.24% and 13.85% than LDPE. The AC breakdown field strength of samples decreased with specimen thickness increase. The DC breakdown field strength of LDPE and ZnO/LDPE composites were greater than AC breakdown field strength. From the conductivity experimental result it could be seen that when the experimental temperature and electric field intensity rose, the current density and conductivity of ZnO/LDPE composites increased with the enlargement of ZnO particles size. But the values were less than which of LDPE.
本文采用熔融共混法制备了3 wt%的氧化锌/低密度聚乙烯(ZnO/LDPE)纳米复合材料。探究了不同无机氧化锌颗粒掺杂对LDPE基体介电性能和晶体习性的影响。纳米颗粒尺寸分别为9 nm、30 nm、100 nm和200 nm。使用扫描电子显微镜(SEM)对氧化锌纳米颗粒进行表征,而差示扫描量热法(DSC)用于对样品进行热表征。此外,本文还研究了纳米复合材料的交流(AC)、直流(DC)击穿特性和电导率。实验结果表明,由于纳米氧化锌颗粒的掺杂,纳米氧化锌/LDPE复合材料具有晶体尺寸小、结晶速率高和结晶度高等优点,当掺杂纳米氧化锌颗粒尺寸为30 nm时,ZnO/LDPE纳米复合材料结晶度峰值出现,为39.77%。同时,复合材料的直流和交流击穿场强值分别为138.0 kV/mm和340.4 kV/mm。它们是最大值,比LDPE提高了8.24%和13.85%。样品的交流击穿场强随试样厚度增加而降低。LDPE和ZnO/LDPE复合材料的直流击穿场强均大于交流击穿场强。从电导率实验结果可以看出,当实验温度和电场强度升高时,ZnO/LDPE复合材料的电流密度和电导率随氧化锌颗粒尺寸的增大而增加。但这些值小于LDPE的值。