Department of Orthodontics, School of Dentistry, Policlinico Universitario "Vittorio Emanuele", University of Catania, Catania, Italy.
Department of Orthodontics, School of Dentistry, Pharos University, Alexandria, Egypt.
Clin Oral Investig. 2021 Apr;25(4):1775-1785. doi: 10.1007/s00784-020-03480-5. Epub 2020 Aug 2.
The purpose of this study was to evaluate mandibular asymmetry in youngsters with posterior unilateral crossbite (PUXB), through cone-beam computed tomography and reverse engineering technique, before and after rapid maxillary expansion (RME) treatment.
Forty cone-beam computed tomography (CBCT) images were obtained from all patients at two time points, namely T0 acquired before the placement of a Hyrax expander and T1 after appliance removal. The CBCT scans were segmented and volume rendered into a surface there-dimensional (3D) mesh model. Thereafter, mandibular models were digitally registered by using a "best-fit" algorithm. Surface and volumetric changes, between T0 and T1, were compared by using Student's t tests.
A slight increase of 0.45 cm of the total mandibular volume was found at T1 when compared with T0 (p < 0.001). The mandibular hemi-volume on the crossbite side (CB) was slightly smaller than the non-crossbite side both at T0 and T1. However, the mean differences of hemi-volume from the CB (crossbite) and non-CB side between T0 and T1 show a decrease of 0.26 cm (p < 0.001). Findings for the surface-to-surface deviation analysis demonstrated a fine percentage of matching at T0 which slightly improved at T1 (p < 0.001).
Youngsters affected by PUXB showed a very slight and not statistically significant volumetric and morphological asymmetry between CB side and non-CB side at T0. However, the change in mean differences of 0.26 cm cannot be considered clinically relevant.
Mandibles in young PUXB patients exhibit only a very mild mandibular asymmetry. Although the statistically significant mean change found right after RME removal cannot be considered clinically relevant, a more consistent sample and a longer follow-up could be of interest in explaining the short-term findings.
本研究通过锥形束 CT 和逆向工程技术,评估后单侧牙弓拥挤(PUXB)青少年在快速上颌扩张(RME)治疗前后的下颌不对称情况。
将 40 名患者的 40 个锥形束 CT(CBCT)图像分别在两个时间点(T0,放置 Hyrax 扩张器前;T1,矫治器拆除后)采集。将 CBCT 扫描进行分割并体积渲染成表面三维(3D)网格模型。然后,使用“最佳拟合”算法对下颌模型进行数字配准。通过 Student's t 检验比较 T0 和 T1 之间的表面和体积变化。
与 T0 相比,T1 时总下颌体积轻微增加 0.45cm(p<0.001)。T0 和 T1 时,患侧(CB)下颌半体积均小于非患侧。然而,T0 和 T1 时从 CB(患侧)和非 CB 侧的半体积平均差异显示出 0.26cm 的减小(p<0.001)。表面到表面偏差分析的结果表明,T0 时的匹配率非常高,T1 时略有提高(p<0.001)。
患有 PUXB 的青少年在 T0 时患侧和非患侧之间的体积和形态不对称非常轻微,且无统计学意义。然而,0.26cm 的平均差异变化不能被认为具有临床相关性。
患有 PUXB 的年轻患者的下颌仅表现出非常轻微的下颌不对称。虽然 RME 拆除后发现的具有统计学意义的平均变化不能被认为具有临床相关性,但更一致的样本和更长的随访可能有助于解释短期发现。