Ding Nannan, Hosein Ian D
Department of Biomedical and Chemical Engineering, Syracuse University, Syracuse, New York 13244, United States.
ACS Appl Energy Mater. 2023 Jun 9;6(12):6646-6655. doi: 10.1021/acsaem.3c00687. eCollection 2023 Jun 26.
We present the properties and performance of fluorescent waveguide lattices as coatings for solar cells, designed to address the significant mismatch between the solar cell's spectral response range and the solar spectrum. Using arrays of microscale visible light optical beams transmitted through photoreactive polymer resins comprising acrylate and silicone monomers and fluorescein ,'-dimethacrylate comonomer, we photopolymerize well-structured films with single and multiple waveguide lattices. The materials exhibited bright green-yellow fluorescence emission through down-conversion of blue-UV excitation and light redirection from the dye emission and waveguide lattice structure. This enables the films to collect a broader spectrum of light, spanning UV-vis-NIR over an exceptionally wide angular range of ±70°. When employed as encapsulant coatings on commercial silicon solar cells, the polymer waveguide lattices exhibited significant enhancements in solar cell current density. Below 400 nm, the primary mode of enhancement is through down-conversion and light redirection from the dye emission and collection by the waveguides. Above 400 nm, the primary modes of enhancement were a combination of down-conversion, wide-angle light collection, and light redirection from the dye emission and collection by the waveguides. Waveguide lattices with higher dye concentrations produced more well-defined structures better suited for current generation in encapsulated solar cells. Under standard AM 1.5 G irradiation, we observed nominal average current density increases of 0.7 and 1.87 mA/cm for single waveguide lattices and two intersecting lattices, respectively, across the full ±70° range and reveal optimal dye concentrations and suitable lattice structures for solar cell performance. Our findings demonstrate the significant potential of incorporating down-converting fluorescent dyes in polymer waveguide lattices for improving the current spectral and angular response of solar cell technologies toward increasing clean energy in the energy grid.
我们展示了作为太阳能电池涂层的荧光波导晶格的特性和性能,其设计目的是解决太阳能电池光谱响应范围与太阳光谱之间的显著不匹配问题。通过由丙烯酸酯、硅氧烷单体和荧光素二甲基丙烯酸酯共聚单体组成的光反应性聚合物树脂传输的微米级可见光光束阵列,我们光聚合出具有单波导晶格和多波导晶格的结构良好的薄膜。这些材料通过蓝-紫外激发的下转换以及染料发射和波导晶格结构的光重定向,呈现出亮绿黄色荧光发射。这使得薄膜能够在±70°的极宽角度范围内收集更广泛的光谱,涵盖紫外-可见-近红外光。当用作商业硅太阳能电池的封装涂层时,聚合物波导晶格在太阳能电池电流密度方面表现出显著增强。在400nm以下,增强的主要模式是通过下转换、染料发射的光重定向以及波导的收集。在400nm以上,增强的主要模式是下转换、广角光收集、染料发射的光重定向以及波导的收集的组合。具有更高染料浓度的波导晶格产生更明确的结构,更适合封装太阳能电池中的电流产生。在标准AM 1.5 G辐照下,我们观察到在整个±70°范围内,单波导晶格和两个相交晶格的标称平均电流密度分别增加了0.7和1.87 mA/cm²,并揭示了用于太阳能电池性能的最佳染料浓度和合适的晶格结构。我们的研究结果表明,在聚合物波导晶格中掺入下转换荧光染料对于改善太阳能电池技术的当前光谱和角度响应以增加电网中的清洁能源具有巨大潜力。