Masri Syafira, Maarof Manira, Aziz Izhar Abd, Idrus Ruszymah, Fauzi Mh Busra
Centre for Tissue Engineering and Regenerative Medicine, Faculty of Medicine, Universiti Kebangsaan Malaysia, Cheras, Kuala Lumpur 56000, Malaysia.
3D Gens Sdn Bhd, 18, Jalan Kerawang U8/108, Bukit Jelutong, Shah Alam 40150, Malaysia.
Int J Bioprint. 2023 Feb 7;9(3):677. doi: 10.18063/ijb.677. eCollection 2023.
3D bioprinting technology is a well-established and promising advanced fabrication technique that utilizes potential biomaterials as bioinks to replace lost skin and promote new tissue regeneration. Cutaneous regenerative biomaterials are highly commended since they benefit patients with larger wound sizes and irregular wound shapes compared to the painstaking split-skin graft. This study aimed to fabricate biocompatible, biodegradable, and printable bioinks as a cutaneous substitute that leads to newly formed tissue post-transplantation. Briefly, gelatin (GE) and polyvinyl alcohol (PVA) bioinks were prepared in various concentrations (w/v); GE (6% GE: 0% PVA), GPVA3 (6% GE: 3% PVA), and GPVA5 (6% GE: 5% PVA), followed by 0.1% (w/v) genipin (GNP) crosslinking to achieve optimum printability. According to the results, GPVA5_GNP significantly presented at least 590.93 ± 164.7% of swelling ratio capacity and optimal water vapor transmission rate (WVTR), which is <1500 g/m/h to maintain the moisture of the wound microenvironment. Besides, GPVA5_GNP is also more durable than other hydrogels with the slowest biodegradation rate of 0.018 ± 0.08 mg/h. The increasing amount of PVA improved the rheological properties of the hydrogels, leading the GPVA5_GNP to have the highest viscosity, around 3.0 ± 0.06 Pa.s. It allows a better performance of bioinks printability via extrusion technique. Moreover, the cross-section of the microstructure hydrogels showed the average pore sizes >100 μm with excellent interconnected porosity. X-ray diffraction (XRD) analysis showed that the hydrogels maintain their amorphous properties and were well-distributed through energy dispersive X-ray after crosslinking. Furthermore, there had no substantial functional group changes, as observed by Fourier transform infrared spectroscopy, after the addition of crosslinker. In addition, GPVA hydrogels were biocompatible to the cells, effectively demonstrating >90% of cell viability. In conclusion, GPVA hydrogels crosslinked with GNP, as prospective bioinks, exhibited the superior properties necessary for wound healing treatment.
3D生物打印技术是一种成熟且有前景的先进制造技术,它利用潜在的生物材料作为生物墨水来替代受损皮肤并促进新组织再生。皮肤再生生物材料备受赞誉,因为与费力的分层皮片移植相比,它们能使伤口面积较大和形状不规则的患者受益。本研究旨在制备具有生物相容性、可生物降解且可打印的生物墨水,作为一种皮肤替代物,在移植后能形成新组织。简要地说,以不同浓度(w/v)制备明胶(GE)和聚乙烯醇(PVA)生物墨水;GE(6% GE:0% PVA)、GPVA3(6% GE:3% PVA)和GPVA5(6% GE:5% PVA),随后用0.1%(w/v)京尼平(GNP)交联以实现最佳可打印性。根据结果,GPVA5_GNP的溶胀率能力显著至少达到590.93±164.7%,且具有最佳的水蒸气透过率(WVTR),即<1500 g/m²/h,以维持伤口微环境的湿度。此外,GPVA5_GNP也比其他水凝胶更耐用,其生物降解速率最慢,为0.018±0.08 mg/h。PVA含量的增加改善了水凝胶的流变学性质,使得GPVA5_GNP具有最高的粘度,约为3.0±0.06 Pa·s。这使得通过挤出技术的生物墨水可打印性表现更好。此外,微观结构水凝胶的横截面显示平均孔径>100μm,具有优异的相互连通孔隙率。X射线衍射(XRD)分析表明,水凝胶在交联后保持其无定形性质,并通过能量色散X射线均匀分布。此外,添加交联剂后,通过傅里叶变换红外光谱观察到没有实质性的官能团变化。另外,GPVA水凝胶对细胞具有生物相容性,有效证明细胞活力>90%。总之,与GNP交联的GPVA水凝胶作为有前景的生物墨水,展现出伤口愈合治疗所需的优异性能。